benikigai/plus-onePublic
Plus One
Prototype in design. Every value is a design target.
Product · Cost
Cost
What does one unit cost, and where does the money go?
- 40
- BOM lines
- 0 of 34
- lines priced
No prices yet. 0 of 34 lines have a unit cost, so there's nothing to chart. The bill of materials below shows every line.
| Item | Qty | Unit cost | Rolled up | Supplier |
|---|---|---|---|---|
| Packed unit with cable and card; no back ships asm:packed | 1 | — | no costs yet | — |
| └ Plus One, sealed, nothing attached asm:plus-one | 1 | — | no costs yet | — |
| └ Top shell sub-assembly with board, speaker, haptic and battery asm:core | 1 | — | no costs yet | — |
| └ Top shell with diffuser, plus button and mic gaskets asm:top-sub | 1 | — | no costs yet | — |
| └ Top shell part:top-shell | 1 | — | To be sourced: shell moulderInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Light-ring diffuser part:ring-diffuser | 1 | — | To be sourced: shell moulderInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Plus button part:plus-button | 1 | — | To be sourced: shell moulderInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Mic gasket part:mic-gasket | 2 | — | To be sourced: die-cut converterInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Main board (PCBA) part:main-pcba | 1 | — | no costs yet | To be sourced: EMS for the main boardInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet |
| └ ESP32-S3 module, 16 MB flash, 8 MB PSRAM part:esp32-s3-module | 1 | — | Espressif or an authorised distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ MEMS microphone, bottom port part:mems-mic | 2 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Class-D amp with a capped output part:audio-amp | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Haptic driver part:haptic-driver | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ 6-axis motion sensor part:imu | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Fuel gauge part:fuel-gauge | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Charger with power path part:charger | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Wireless charging receiver part:wireless-receiver | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ RGB LED, addressable part:ring-led | 12 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Tactile switch under the plus part:tact-switch | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ USB-C receptacle, mid-mount part:usb-c | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ BOOT button part:boot-button | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Hardware power-off switch part:power-switch | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Qwiic connector part:qwiic-connector | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Battery connector part:battery-connector | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Bare board, 4 layers part:pcb | 1 | — | To be sourced: EMS for the main boardInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Passives part:passives | 1 | — | To be sourced: component distributorInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Board screw, 2 mm thread-forming for plastics part:board-screw | 3 | — | To be sourced: fastener makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Speaker, 12 mm thin part:speaker | 1 | — | To be sourced: micro speaker makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Haptic motor, 7 mm coin part:haptic-motor | 1 | — | To be sourced: LRA makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Li-ion cell with protection part:battery | 1 | — | To be sourced: Li-ion cell makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Battery foam tape part:battery-foam | 1 | — | To be sourced: die-cut converterInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Base with the magnet ring, charging coil and pads asm:base | 1 | — | no costs yet | — |
| └ Base: the interface part:base | 1 | — | To be sourced: shell moulderInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Magnet ring part:magnet-ring | 1 | — | To be sourced: magnet makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Wireless charging coil and ferrite part:qi-coil | 1 | — | To be sourced: wireless charging coil makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Pogo pad part:pogo-pad | 5 | — | To be sourced: shell moulderInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Retail box part:retail-box | 1 | — | To be sourced: packaging makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Pulp tray part:pulp-tray | 1 | — | To be sourced: packaging makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ USB-C cable, 0.5 m part:usb-cable | 1 | — | To be sourced: packaging makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet | |
| └ Quick start card with the unit QR part:quick-card | 1 | — | To be sourced: packaging makerInferredEngineering judgement, not measured. Low confidence.Evidence:src:design-briefnot sourced yet |