benikigai/plus-onePublic
Plus One
SHA-256 ea5f021cb34d416b8ca2a6df74708b890f0755040bb6bdf3e145b5d645291f5f
{
"schema": "factory-n1/layout/v1",
"revision": 1,
"selection": {
"status": "proposal",
"date": "2026-11-01"
},
"geometry_evidence": "ASSUMPTION",
"calibration_status": "uncalibrated",
"workstations": "manual",
"units": {
"length": "m",
"angle": "rad"
},
"frame": {
"handedness": "right",
"up_axis": "Z",
"origin": "floor corner at minimum X and Y",
"flow_axis": "+X",
"station_pose_anchor": "footprint centre at floor level",
"quaternion_order": "xyzw"
},
"station_geometry_defaults": {
"footprint_m": [
1.2,
0.75
],
"work_surface_height_m": 0.9
},
"id": "plus-one-u-cell",
"label": "Plus One U cell (concept)",
"title": "Plus One · U cell",
"room": {
"size_m": [
6.2,
6.8,
3.0
]
},
"footprint_m": [
5.9,
5.6
],
"stations": [
{
"station_id": "S1",
"position_m": [
1.0,
1.6,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
0.7071068,
0.7071068
],
"label": "Top shell"
},
{
"station_id": "S2",
"position_m": [
1.0,
2.9,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
0.7071068,
0.7071068
],
"label": "Board"
},
{
"station_id": "S3",
"position_m": [
1.0,
4.2,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
0.7071068,
0.7071068
],
"label": "Screws"
},
{
"station_id": "S4",
"position_m": [
2.3,
5.4,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
0.0,
1.0
],
"label": "Adhesive, speaker, haptic"
},
{
"station_id": "S5",
"position_m": [
3.6,
5.4,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
0.0,
1.0
],
"label": "Battery"
},
{
"station_id": "S6",
"position_m": [
4.9,
4.2,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
-0.7071068,
0.7071068
],
"label": "Close the base"
},
{
"station_id": "S7",
"position_m": [
4.9,
2.9,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
-0.7071068,
0.7071068
],
"label": "Flash + calibrate"
},
{
"station_id": "S8",
"position_m": [
4.9,
1.6,
0.0
],
"orientation_xyzw": [
0.0,
0.0,
-0.7071068,
0.7071068
],
"label": "Test and pack"
}
],
"cell": {
"type": "u",
"open_side": "-Y",
"hold_m": [
5.75,
0.75
],
"carton_m": [
4.9,
0.55
]
},
"crews": [
{
"id": "op1",
"count": 1,
"stations": [
"S1",
"S2",
"S3",
"S4",
"S5",
"S6"
]
},
{
"id": "op2",
"count": 1,
"stations": [
"S7",
"S8"
]
}
],
"behavior_binding": {
"station_key": "station_id",
"route_source": "active product sequence",
"station_definition_source": "resolved product station library",
"timing_and_outcome_source": "recorded engine events and results",
"inactive_station_policy": "retain footprint; show inactive; no unit visits"
},
"transport": {
"duration_source": "engine",
"layout_time_model": "not-calibrated"
},
"notes": [
"Concept layout for the 2,000-a-month scenario (studies/plus_one_demand.yaml): the OPD's eight stations as benches in a U open toward -Y, with no powered conveyor. Every position is an ASSUMPTION.",
"Operators work inside the U (2 at this volume: one runs S1 to S6, the other S7 and S8). Parts are fed from outside the U into each bench's rear flow shelves.",
"A unit moves one at a time into the marked single-unit square in front of the next station (the run's hand_pass, 2 s); nothing else holds work in process.",
"A failed unit goes onto a red HOLD shelf outside the U by S8; good units, packed at S8, go into a master carton at the U's mouth. Both are display only.",
"footprint_m is the cell with the feeding aisle outside it; the room is just the drawing's floor.",
"\"crews\" repeats the study's crews (studies/plus_one_demand.yaml) for the viewer, which draws only that many operators at the benches they are working; tests/test_demand_layouts.py keeps the two the same."
]
}